PORTA-MOUNTS · Mounting & Support
A base, clamp, adapter, bracket, stake, or mount for a documented portable installation.
Why operators make room for it
Turn a vehicle, stake, clamp point, or tripod into a working base
Good portable mounting is not glamorous until the wind rises and the operator realizes the entire antenna depends on it.
That is where CHA PORTA-MOUNTS enters the kit. Anodized aluminum " MAST TOPPER " allows mounting antennas with a 3/8x24 stud mount such as our MPAS 2.0, MPAS Lite, TDL, RXL Pro or other similarly mounted antennas, or antennas that use U bolts or clamps. See the Porta Mast user guide for antenna weight and wind loading limits. Topper dimensions are 1.5" Base, 8" Shaft, total length of 10.25".
For the operator, a documented mount turns an improvised-looking site into a predictable installation with the correct adapter, fasteners, load limits, and guying.
Quick product reference
Key Specifications
- Product type
- Mounting & Support
- Primary role
- A base, clamp, adapter, bracket, stake, or mount for a documented portable installation.
- Available style
- GROUND SLEEVE MOUNT 2.5"
- GROUND SLEEVE MOUNT 3"
- HITCH MOUNT
- MAST TOPPER (TOP 3/8-24)
- REDUCER SLEEVE MOUNT 2.5"
- SIDE MOUNT
- TOP MOUNT
- WHEEL MOUNT
- RF role
- Mechanical support; completed antenna determines electrical specifications
- Load rule
- Verify leverage, wind area, adapters, fasteners, and guying
- Structural role
- Base, clamp, bracket, stake, adapter, or mount in a documented load path
- Load planning
- Verify antenna weight, leverage, wind area, vehicle / terrain condition, and fastener strength
- Interface verification
- Confirm every thread, sleeve, adapter, clamp surface, and required fastener
Operator decision support
Plan the complete setup
See what this product is best suited for, what the documented setup needs, and the boundaries to confirm before deployment.
- Best for
Good portable mounting is not glamorous until the wind rises and the operator realizes the entire antenna depends on it.
- What else you need
Confirm the antenna load, leverage, wind area, adapter, sleeve, fastener, and guying requirements.
- Compatible with
Confirm every thread, sleeve, adapter, clamp surface, and required fastener
- Limitations
Verify leverage, wind area, adapters, fasteners, and guying
What an operator can do
- Attach the mount to the approved surface, vehicle point, ground location, or support.
- Confirm the antenna load, leverage, wind area, adapter, sleeve, fastener, and guying requirements.
- Re-check stability and fastener tension after deployment and whenever weather or loading changes.
Complete product details
Hitch Mount:
Powder coated aluminum “HITCH MOUNT”. The end that fits into the receiver is 15″ long and is a 2″x2″ square (outside measurement). The hole for the pin is 5/8″ in diameter. This is used primarily for RV camping or even tailgating in a parking lot! A hitch pin is not provided.
- The 3" GS (Ground Sleeve) is only used if you are putting the mast into the ground for the 20' and 25' masts.OPTIONAL
- The 2.5" GS (Ground Sleeve) is only used for the 15' mast to mount into the ground. OPTIONAL
- The 2.5" RS (Reducer Sleeve) must be used with all mounts which are 3".OPTIONAL
Top Mount:
Powder coated aluminum “TOP MOUNT”. This can be attached to any horizontal surface. Concrete, wood, RV tongue. Attaching hardware is not included. Don’t forget the Reducer Sleeve for Mounts if your pole is the 15′ (2.5″ base). The holes in the base are 7/16″ in diameter, and the centers of the holes are 6 7/8″ apart side to side and top to bottom.
- The 3" GS (Ground Sleeve) is only used if you are putting the mast into the ground for the 20' and 25' masts.OPTIONAL
- The 2.5" GS (Ground Sleeve) is only used for the 15' mast to mount into the ground. OPTIONAL
- The 2.5" RS (Reducer Sleeve) must be used with all mounts which are 3".OPTIONAL
Wheel Mount:
Powder coated aluminum “WHEEL MOUNT”. This is primarily used for RV’s under the tire. You simply park one of your tires on it and set the brake, then drop your flagpole in the hole! The wheel stand plate is 30″ long x 8″ wide.
- The 3" GS (Ground Sleeve) is only used if you are putting the mast into the ground for the 20' and 25' masts.OPTIONAL
- The 2.5" GS (Ground Sleeve) is only used for the 15' mast to mount into the ground. OPTIONAL
- The 2.5" RS (Reducer Sleeve) must be used with all mounts which are 3".OPTIONAL
Mast Topper:
Anodized aluminum "MAST TOPPER" allows mounting antennas with a 3/8x24 stud mount such as our MPAS 2.0, MPAS Lite, TDL, RXL Pro or other similarly mounted antennas, or antennas that use U bolts or clamps. See the Porta Mast user guide for antenna weight and wind loading limits. Topper dimensions are 1.5" Base, 8" Shaft, total length of 10.25".
Don’t forget the Reducer Sleeve for Mounts if your pole is a 15′ (2.5″ base). OPTIONAL
- NO LOCAL PICK-UP FOR THAT PRODUCT
- For international Alaska and Hawaii please email us for a Shipping Quote.
